Why is My Dishwasher Leaking?

Getting up in the morning only to step in an ominous puddle on the floor is never a great to start the day.

Luckily, most simple explanations of dishwasher leaks are comparatively straightforward to pinpoint and mend on your own. This means you may not have to wash the dishes by hand that much, spend a day at home waiting for an repair person or have to pay a high call-out charge.

So, if you’re feeling up to it grab the instruction manual if you know where it is, clean up the puddle and so get a towel clean up any additional spills and so see whether you can’t diagnose the fault. If you aren’t able to call us for local dishwasher repair.

Simple Sources of Dishwasher Faults as well as How to Fix Them

A lot of the more commonplace sources of dishwasher faults aren’t actually a result of a broken dishwasher at all. Prior to starting preparing yourself for an engineering task and also watching endless online tutorials there are a number of issues you might want to troubleshoot first.

  1. Check to find out whether your dishwasher is aligned. If your dishwasher is wonky water can quickly pool as well as spill out without there being anything that needs to be fixed or replaced.
  2. Test you have been using the correct detergent. You might have seen this with your washer. An excess of soap or the incorrect type may result in an excess of bubbles, the bubbles deluge and so you get a leak.
  3. Check your dishwasher door closes fully. If it doesn’t you may have something obstructing it, or you may need to adjust the hinge or the locking mechanism.
  4. Investigate the filter located in the bottom of the tub for any obvious drainage issues as if your dishwasher isn’t emptying effectively this will cause it to overfill and leak.

If you have looked at these possible causes it’s time to roll up your sleeves and really begin a thorough check.

To make your life easier start with the door and test for any obvious damage in the interior of the machine before you move on to the underneath. If you can identify and fix the issue before you need to pull out the dishwasher so much the better.

And make sure you disconnect the appliance first by either unplugging it or turning off the circuit breaker for the dishwasher.

Door Seal

The door is no doubt the most commonplace area for leakage as well as one of the easiest problems to solve.

If the leakage is intermittent the issue may be as straightforward as a large plate or something else putting pressure into the door and preventing it from closing fully.

Else-ways the door gasket might have come out of place or become damaged.

Inspect the door seal and also investigate for any brittleness, mineral deposits or other deposits, or any parts where the gasket has separated from the door.

Removing the gasket and also giving it a good scrub could improve the situation in some cases or you could need to purchase a new seal and replace it.

Water Inlet Valve (Solenoid Fill Valve)

The inlet valve can also be a common fault. The Valve is usually located under the machine and so you will need to unscrew the kick plate and may need to remove the door cover.

The fill valve opens and also closes to allow water into the dishwasher at different parts of the programme. The water inlet valve may be showing a leak, shown with a slight drip, or it might be broken thus not functioning correctly while the dishwasher is running.

If the water inlet valve fails to close correctly this can mean that the dishwasher overfills, causing a leak.

Usually these valves are not able to be refurbished unless it is only the rubber seal that is broken, which means the whole valve would need to be changed.

Leaking Hoses

Hoses are needed to supply, empty and also redistribute water during the programme.

Two issues can develop with hoses.

  1. The seals might get damaged or the contact points can come loose thus it’s a good idea to have a look at all the connection points first.
  2. The alternative fault than could often develop as time goes by is that hoses might get damaged or cracked.

Luckily faulty hoses are relativelyeasy to buy and replace, even for a novice.

Pumps and Seals

You can visually investigate the seals around the water pumps or motor to see if there is a leakage and change them if there is.

The Float Switch

The float itself or the float switch could be not working correctly causing the dishwasher to overfill.

A working float will go up as the water rises until the optimum or highest water level is reached. The tail of the float would then turn on the switch. If something is blocking this or the float is broken this could be your issues.

Checking the switch will require a multi-meter although it may be noticeably broken in which case replacing it should solve the leak.

Alternative Parts that Might Result in a Leak

A damaged wash arm or support could build up pressure causing a leak. This will also often result in your dishes not being cleaned as effectively as they should.

Broken or faulty tubes could also result in this problem as might a broken pump cap.

The motor shaft seal could have come loose resulting in leakage. This generally presents as leakage coming from the underside of the appliance.

Top Tips to Sort Out Your Machine

  1. Save money by checking the seal instead of the entire component. In most instances, you are able to purchase the gasket separately which saves time as well as money.
  2. Investigate the simple fixes first. There’s no point pulling the whole dishwasher out if it’s the soap that’s causing the issue.
  3. Photograph your progress. This might assist you to reverse the process, describe the part you need in a shop, and explain the problem to an engineer if needed.
  4. Be careful. Water and electricity do not mix so unplug the machine first.
  5. If in doubt call a professional.

What To Do Next If Your Trouble Shooting Fails to Identify or Fix the Leak

If the root of the leakage can’t be discovered the next step you can take is to pull the dishwasher away from the wall to get better access beneath it and add water to the tub to find out if the leak presents itself.

If you don’t discover any faults with this method your machine may only leak if the pump is running. In this case, you should get a dishwasher repair person to pinpoint and fix the issue as there are safety risks of running the dishwasher with electrical elements exposed.

More Dishwasher Problems:

CLICK-TO-CALL